How To Use BareSpot Monobor-Chlorate Herbicide

BareSpot Monobor-chlorate is safe for use around pets and children when used in accordance with the instructions on the product label.

Wear the appropriate personal protective equipment when handling and applying BareSpot Monobor-Chlorate.

BareSpot Monobor chlorate can be spread by hand or using any spreader that is suitable for granular fertilizers. The pellets can be seen, so there are no “misses” or “skips”. No guesswork is involved.

Keep reading to find out more!

 

How Do I Describe the BareSpot Monobor-Chlorate Herbicide?

Barespot Monobor-Chlorate
Picture of the BareSpot Monobor-Chlorate

BareSpot Monobor Chlorate is an effective non-selective weed killer that kills a wide range of weeds, grasses, and weed seeds in one treatment.

The dry, ready-to-use formulation of the granules eliminates any risk of over-application or drift. Water the granules to instantly control unwanted vegetation, including perennial and broadleaf weeds.

The combination of two active ingredients Sodium Metaborate (48.5%) and Sodium Chlorate (30%) provides immediate knockdown as well as long-lasting residual control on non-crop surfaces.

BareSpot Monobor Chlorate controls bare-ground vegetation for a season and prevents future growth. One treatment will provide residual control for 6 to 9 months on hard-to-control weeds as well as new seedlings.

 

Read also: How To Use BareSpot Ureabor Herbicide

 

How To Use BareSpot Monobor-Chlorate Herbicide?

  • Do Your Calculations:

Multiply the length and width (length X Width = square footage) to get the area. For general weed control, the application rate is 2 pounds. BareSpot Monobor Chlorate is applied at a rate of 2 lbs. ft..

Use 4 lbs. per 100 sq. Use 4 lbs. To use as a “prepaving” residual weed killer under asphalt paving, apply 2-4 pounds of product per 100 square feet. As a dry application.

Pour a spray application, and dissolve 1-2 lbs. Pour a spray application, and dissolve 1-2 lbs. ft. Inject BareSpot Monobor-Chlorate into the cracks caused by emerging vegetation. Per gallon of water.

  • Follow The BareSpot Monobor-Chlorate Herbicide Label Instructions:

Use a spreader or sprayer calibrated to the correct setting and load the BareSpot Monobor chlorate in the desired amount.

Pour spray application, pour the remaining half, fill the sprayer half with water, then add the product. Shake until it is well mixed. Let it dissolve.

  • Apply:

For best results, apply BareSpot Monobor chlorate evenly over the desired area and water in BareSpot Monobor chlorate immediately following application.

BareSpot should not be applied near the roots or desired vegetation.

 

Read also: How To Use Gly Pho-Sel Pro Dry 75 SG Herbicide

 

According to the BareSpot Monobor-Chlorate Herbicide Label Where Can I Apply?

  • Gravel driveways
  • Sidewalks
  • Walkways
  • Fence lines
  • Outbuilds & sheds
  • Bleachers
  • Bridge abutments
  • Buildings
  • Bunkers
  • Buried cable closures
  • Catwalks
  • Cemeteries
  • Compressor stations
  • Cooling towers
  • Cross-connect boxes
  • Electrical generators
  • Fence lines
  • Fire hydrants
  • Plugs or wall
  • Fuel tanks
  • Generating plants
  • Guardrails
  • Helo pads
  • Highway & street markers
  • Loading stations
  • Lumber yards
  • Microwave towers
  • Oil & Gas pipelines
  • Oil refineries
  • Parking lots
  • Pump decks
  • Runway lights
  • Runways
  • Signposts
  • Storage & equipment yards
  • Utility poles & substations
  • Vacant lots
  • Valvers & manifolds
  • Waste lagoons

 

When Do I Use the BareSpot Monobor-Chlorate Herbicide?

BareSpot monobor-chlorate is ideal for removing all vegetation from an area. It is easier to eliminate weeds and grasses when they are growing quickly and are still young.

 

What are the Target Pests of the BareSpot Monobor-Chlorate Herbicide?

  • Annual weeds
  • Perennial weeds
  • Trees
  • Shrubs
  • Broadleaf weeds
  • Grasses

 

Read also: How To Use Triumph 22K Picloram Herbicide

 

What Is the Shelf Life According to the BareSpot Monobor-Chlorate Label?

When stored in a dry, cool place, Barespot monobor-chlorate can last up to three years. With a single application, Bare Spot Monobor Chlorate kills quickly and non-selectively.

 

Additional Product Information?

What are the Active Ingredients?
  • 48.5 % Of Sodium Metaborate
  • 30.0 % Of Sodium Chlorate
What are the Possible Areas of Application? Outdoors
What Is the Chemical Type? Herbicide
Does this Product Have any Usage Restrictions? No
Which Products Can Be Compared To This Product? Bromacil Bare Ground Herbicide
Is It Safe To Use Around Children and Pets? Yes, it is safe to use around children and pets.
What Is Its Formulation? Granular

 

Where To Buy BareSpot Monobor-Chlorate Herbicide For Sale?

About The Author


Discover more from Pestclue

Subscribe to get the latest posts sent to your email.

Leave a feedback

This site uses Akismet to reduce spam. Learn how your comment data is processed.